Quick answer
Window security bars are a physical barrier against break-ins. Burglars favor targets they can enter quickly and quietly. A steel bar removes the smash-and-grab option and forces a slower, louder, more visible entry. For most homes: Model A fits most standard windows, DIY in 15–30 min with a drill, $85 per module. Bedroom windows need quick release from inside (Model A/EXIT, designed to meet IRC R310.4.4 / IBC § 1031.6; verify with your local AHJ). Permit rules vary, so check locally.
What are window security bars?
Burglars often size up a home quickly, standing at the edge of the property and scanning ground-floor windows. Doors and windows are the usual ways in, and an opening that looks hard to get through quietly gives them a reason to move on.
Window security bars are physical barriers installed over window openings to prevent unauthorized entry. Unlike an alarm, which detects entry after the fact, bars are designed to physically block entry through the window, and the two work well together.
Modern window bars have evolved significantly from the welded iron bars of the past. Today's systems can be adjustable, clean-looking, and offer quick release from inside for bedrooms, addressing the main objections that historically made bars unpopular. This guide covers everything you need to make the right decision.
An alarm tells you someone got in. A window bar is there to make getting in through that window much harder.
Types of window security bars
The five main categories are telescopic + modular (adjustable, most versatile), fixed welded steel (heavy-duty, permanent), no-drill / tension (renter-friendly, lower security), decorative / ornamental (aesthetic focus), and quick-release / egress (needed for bedrooms). For many homeowners, adjustable + modular bars offer a good balance of security, fit, and a quick-release option for bedrooms.
Telescopic + Modular
Versatile: adjusts to most standard windows
Fixed Steel Guards
Heavy-duty: permanent installation
No-Drill / Tension
Renter-friendly: no holes required
Decorative / Ornamental
Aesthetic focus: wrought iron designs
Quick-Release / Egress
Needed on bedroom windows (egress)
How to choose the right window bar
Consider these four factors:
Window Size & Type
Measure your clear opening: width (jamb to jamb) and height. If you have non-standard or varying window sizes, a telescopic + modular system saves significant money and effort vs. buying custom bars.
Wall/Frame Material
Wood or vinyl frames: Model A works perfectly with frame-mount hardware. Masonry, concrete, stucco: Model B is designed specifically for wall-mount on these surfaces.
Fire Code Requirements
If you're installing bars on bedroom windows, the IRC (R310.4.4) and IBC (§ 1031.6) require bars on emergency escape openings to release from inside without keys, tools or special knowledge. Use Model A/EXIT for any sleeping area and confirm with your local AHJ.
Budget
SWB bars are $85 per 16-inch module in all three models. A 48-inch window takes 3 modules ($255). Use our Cost Calculator to estimate your total project cost.
Installation guide overview
SWB bars are designed for DIY installation in 15–30 minutes per window. All hardware and anchors are included. You need: a standard drill, measuring tape, pencil, and bubble level.
Measure
Clear width + clear height. Write these down.
Mark & Drill
4 mounting points. Use included anchors for your wall type.
Install & Test
Insert bars, adjust to size, tighten screws. Verify with level.
Fire code requirements
The most important thing to know: Bars over a bedroom's emergency escape window must release from inside without tools, keys or special knowledge.
This is set out in IRC R310.4.4 and IBC § 1031.6, which most US jurisdictions adopt, sometimes with local amendments, so always confirm with your local building department.
- Bars without quick-release: Can block an emergency escape route
- Bars without quick-release: May not pass local code inspection
- Bars without quick-release: Expose homeowners to liability
SWB Model A/EXIT is designed to meet the emergency-escape requirements for bars in IRC R310.4.4 and IBC § 1031.6: from inside, lift the end tube and the module swings open like a door, with no keys, no tools, no add-on kit. Confirm with your local AHJ. Model A and Model B do not have quick release.
How much do window security bars cost?
| Option | Cost per window | Notes |
|---|---|---|
| Store-bought DIY bars | Varies | Check the listing for sizes and release options |
| SWB Direct (modular) | $85/module (48″ window: $255) | Adjustable; quick release on Model A/EXIT |
| Professional install | Varies: get a local quote | Custom + labor |
| Heavy-duty commercial | Varies: get a local quote | Custom fabrication, pro install |
Top brands compared
The window bar market has several players. Here's a quick overview. Check each brand's current specs before you buy:
SWB (Security Window Bars)
Adjustable + modular system, quick release on Model A/EXIT, $85 per module.
Grisham
Sold at home-improvement retailers. Check the listing for sizes and release options.
Mr. Goodbar
Window security bar brand. Check their current specs for sizes and release options.
Unique Home Designs
Security products brand. Check their current specs.
Home Depot / Lowe's store brands
In-store options. Check each listing for sizes, materials and release options.
Related guides
Written and reviewed by the Security Window Bars product team.
Security Window Bars writes and reviews the technical content on this site. Code references point to the IRC and IBC so you can verify them yourself. Final approval is always up to your local authority having jurisdiction (AHJ).